vicor corp. tel: 800-735-6200, 978-470-2900 fax: 978-475-6715 pfc flatpac rev. 1.4 page 1 of 7 set your site on vicor at vicorpower.com v out 5 v v out 12 v q = 80 a m = 575 w features ? inputs: 85 C 264 vac universal ? meets fcc part 15, en55022, class a conducted emissions ? 75-85% efficiency ? ctvvs, ce marked ? remote sense and current limit ? 8-60 ms ride-through time ? ovp and thermal shutdown ? up to 575 w output product highlights the pfc flatpac uses vicors field-proven vi-ham and maxi dc-dc converters to deliver up to 575 watts of clean, reliable power. the pfc flatpac is a single-output power supply available with standard output voltages from 3.3 C 54 vdc. it operates from an input of 85 C 264 vac, includes active power factor correction (0.99 power factor), and meets en61000-3-2 har- monic current limits. internal filtering pro- vides compliance to en55022-a conducted emi. it is available in vicors low profile 1.37" (34,8 mm) flatpac chassis, in either finned or conduction- cooled (cc) versions. data sheet pfc flatpac tm 575 w power factor corrected ac-dc power supply e = 0 to + 85 c a se c = 0 to + 85 c a se i = ? 30 to + 85 c a se y = 3.3 v 0 = 5.0 v 1 = 12 v 2 = 15 v 3 = 24 v l = 28 v j = 36 v 4 = 48 v g = 54 v product grade temps. ( c) output power/current vout output voltage cc = cond u ction cooled options v i -cmu - - [a] e for rohs compliant pfc flatpac selection chart [a] actual size: 9.25 x 4.9 x 1.37 in 234,8 x 124,4 x 34,8 mm
vicor corp. tel: 800-735-6200, 978-470-2900 fax: 978-475-6715 pfc flatpac rev. 1.4 page 2 of 7 set your site on vicor at vicorpower.com e-grade c-, i-grade min typ max min typ max units note set point a cc u r a cy 1% 2% 0.5% 1% v nom line reg u l a tion low line 0.5% 0.02% 0.2% v nom 85 ? 264 v a c, 0 ? 350 w nomin a l to high line 0.5% 0.02% 0.2% v nom 115 ? 264 v a c, 0 ? 575 w lo a d reg u l a tion low line 1% 0.2% 0.5% v nom 85 ? 264 v a c, 0 ? 350 w nomin a l to high line 1% 0.2% 0.5% v nom 115 ? 264 v a c, 0 ? 575 w o u tp u t temper a t u re drift 0.02 0.01 0.02 %/c over r a ted temper a t u re long term drift 0.02 0.02 %/1 k ho u rs o u tp u t ripple 3.3 v 150 120 150 mvp-p 20 mhz ba ndwidth 5 v 5% 120 150 mvp-p 20 mhz ba ndwidth 12-54 v 3% 2% 3% p-p 20 mhz ba ndwidth o u tp u t volt a ge trimming 10% 110% 10% 110% see vicorpower.com for trim c a lc u l a tor to t a l remote sense compens a tion 0.5 0.5 volts 0.25 v m a x. neg. leg ovp set point 125% 115% 120% 125% v nom recycle power c u rrent limit 102% 135% 102% 135% i nom a u tom a tic rest a rt short circ u it c u rrent 70% 140% 70% 135% i nom parameter min typ max unit note ac line inp u t univers a l 85 264 v a c unit will oper a te a t 400 hz bu t m a y not meet line freq u ency 47 ? 63 hz power f a ctor or tot a l h a rmonic distortion specs. efficiency m a y b e red u ced. inr u sh c u rrent 230 v a c oper a tion, f u ll lo a d20a ride-thro u gh time (f u ll lo a d) 85 ? 264 v a c 8 60 ms dielectric withst a nd prim a ry to ch a ssis gnd 2,121 vdc prim a ry to second a ry 4,242 vdc second a ry to ch a ssis gnd 707 vdc power f a ctor 0.99 to t a l h a rmonic distortion 7.5% sin u s u id a l, 115 v a c, f u ll lo a d 8.5% sin u s u id a l, 230 v a c, f u ll lo a d flatpac specifications (typical at = 25c, 120/240 vac line and 75% load, unless otherwise specified) input characteristics output characteristics (see d a t a sheet for v375 m a xi f a mily for a ddition a l info)
vicor corp. tel: 800-735-6200, 978-470-2900 fax: 978-475-6715 pfc flatpac rev. 1.4 page 3 of 7 set your site on vicor at vicorpower.com e-grade c-, i-grade min typ max min typ max units note efficiency 70 ? 80% 75 ? 85% sh u t down temp. ? c a se 90 95 105 90 95 105 c cool a nd recycle power to rest a rt oper a ting temp. ? c a se 85 85 c see therm a l c u rves parameter min typ max unit note weight 44.8 (1304) o u nces (gr a ms) ctv u s ul 60950-1, csa 60950-1, en60950-1, iec 60950-1 ce low volt a ge directive 73/23/eec parameter min typ max unit note stor a ge temper a t u re -20 to +100 c c-gr a de a nd e-gr a de -55 to +100 c i-gr a de oper a ting temper a t u re (c a se) 0 to +85 c c-gr a de a nd e-gr a de -30 to +85 c i-gr a de parameter min typ max unit note cond u cted emissions en 55022:1998, cispr 22, cl a ss a r a di a ted emissions en 55022:1998, cispr22, cl a ss b h a rmonic c u rrent emissions en 61000-3-2:2000 volt a ge fl u ct ua tions a nd flicker en 61000-3-3:1995 electrost a tic disch a rge en 61000-4-2, level 4, 8 kv cont a ct, 15 kv a ir disch a rge rf r a di a ted imm u nity, e-field en 61000-4-3, 80 mhz to 2.0 ghz, 10 v/m electric a l f a st tr a nsients/ bu rst en 61000-4-4, level 3; 500 v, 1 kv a nd 2 kv power line s u rge imm u nity en 61000-4-5, level 3; 500 v, 1 kv, 1.5 kv a nd 2 kv rf cond u cted imm u nity en 61000-4-6, level 3; 150 khz to 80 mhz, 10 vrms power freq u ency h-field imm u nity en 61000-4-8, level 4; 30 a/m, contin u o u s field volt a ge dips a nd interr u pts en61000-4-11 flatpac specifications (typical at = 25c, 120/240 vac line and 75% load, unless otherwise specified) thermal characteristics mechanical specifications safety agency approvals evironmental characteristics/product grade designators emi / emc characteristics (performed on selected s a mples represent a tive of the pfc fl a tpac prod u ct f a mily.)
vicor corp. tel: 800-735-6200, 978-470-2900 fax: 978-475-6715 pfc flatpac rev. 1.4 page 4 of 7 set your site on vicor at vicorpower.com ac m a ins e a rth gro u nd l1 l2/n gnd 0 100 200 3 00 400 500 600 0 5 10 15 20 25 3 0 3 54045505560657075 8 0 8 5 ambient temperature (c) output power (watts) figure 1 output power derating vs. temperature, vout 12 v 0 50 100 150 200 250 3 00 3 50 400 0 5 10 15 20 25 3 0 3 54045505560657075 8 0 8 5 ambient temperature (c) output power (watts) figure 2 output power derating vs. temperature, vout = 5 v figure 4 pfc flatpac output power vs. input voltage 0 24 4 8 72 96 120 144 16 8 192 216 240 264 0 5 10 15 20 25 3 0 3 54045505560657075 8 0 8 5 ambient temperature (?) output power (watts) figure 3 output power derating vs. temperature, vout = 3.3 v figure 5 ac input connections figure 6 electrical connections note: all temper a t u re der a ting performed a t 120 v a c inp u t free air 200 lfm 400 lfm 600 lfm 8 00 lfm 1000 lfm inputs 7 ac in l1 8 ac in l2/n 9 chassis gnd outputs 10 +out (#10-32 st u d) 11 +out 12 +sense 13 trim 14 ?sense 15 ?out 16 ?out (#10-32 st u d) te r m i n a ls for #16-12 awg wire o u tp u t connector, amp p/n 644486-5; m a ting connector, mta-100 idc series note: pins 1-6 connected to ch a ssis gnd (not used). 350 375 400 425 450 475 500 525 550 575 600 85 105 125 145 165 185 205 225 245 265 vin (vrms) pout (w)
vicor corp. tel: 800-735-6200, 978-470-2900 fax: 978-475-6715 pfc flatpac rev. 1.4 page 5 of 7 set your site on vicor at vicorpower.com 3 00 3 50 400 450 500 550 600 85 110 135 160 185 210 235 260 input voltage (vac) output power (watts) figure 8 output power start-up de-rating @ C30 c (i-grade only). 5 minute warm up required before full power (see figure 4) is available. 0 100 200 300 400 500 600 20 25 30 35 40 45 50 55 60 65 70 75 80 85 ambient temperature (c) output power (w) 80 60 70 50 cold plate temp (c) figure 7 power de-rating conduction cooled option optional filter to meet en55022 class b compliance l1 l1 l2/n pe c2 in ext. filter l1 l2/n pe c1, c2: p/n 00927 f1: p/n 32810 l1: p/n 31742 330 nf c1 in in f1 out out out pfc fl a tpac
vicor corp. tel: 800-735-6200, 978-470-2900 fax: 978-475-6715 pfc flatpac rev. 1.4 page 6 of 7 set your site on vicor at vicorpower.com mounting hole ?0.15 ?.01 thru 5 places 10 11 12 13 14 15 16 7 8 9 4.562 ?.010 (115,87 ?,25) 2.281 ?.010 (57,94 ?,25) 0.199 ?.010 (5,05 ?,25) 0.18 (4,57) 6.00 (152,4) 4.960 ?.030 (125,98 ?,76) 3.83 (97,16) 1.17 (29,72) 10 11 12 13 14 15 16 10 11 12 13 14 15 16 output 1 output 2 + + ? 1. 3 75 0.020 ( 3 4,91 0,51) 0.50 (12,57) 9.245 0.0 3 0 (2 3 4, 8 2 0,76) 1.11 ( 2 8 ,19) figure 9a mechanical drawings; convection cooled. figure b mechanical drawings; conduction cooled.
vicor corp. tel: 800-735-6200, 978-470-2900 fax: 978-475-6715 pfc flatpac rev. 1.4 04/09 set your site on vicor at vicorpower.com vicor corporation 25 front a ge ro a d andover, ma, usa 01810 tel: 800-735-6200 f a x: 978-475-6715 email vicor express: vicorexp@vicr.com technic a l s u pport: a pps@vicr.com vicors comprehensive line of power solutions includes high density ac-dc and dc-dc modules and accessory components, fully configurable ac-dc and dc-dc power supplies, and complete custom power systems. information furnished by vicor is believed to be accurate and reliable. however, no responsibility is assumed by vicor for its use. vicor components are not designed to be used in applications, such as life support systems, wherein a failure or malfunc- tion could result in injury or death. all sales are subject to vicors terms and conditions of sale, which are available upon r e- quest. specifications are subject to change without notice. intellectual property notice vicor and its subsidiaries own intellectual property (including issued u.s. and foreign patents and pending patent ap- plications) relating to the products described in this data sheet. interested parties should contact vicor's intellectual property department. warranty vicor products are guaranteed for two years from date of shipment against defects in material or workmanship when in normal use and service. this warranty does not extend to products subjected to misuse, accident, or improper application or mainte- nance. vicor shall not be liable for collateral or consequential damage. this warranty is extended to the original purchaser only. except for the foregoing express warranty, vicor makes no warranty, express or implied, including, but not limited to, the warranty of merchantability or fitness for a particular purpose. vicor will repair or replace defective products in accordance with its own best judgement. for service under this warranty, the buyer must contact vicor to obtain a return material authorization (rma) number and shipping instructions. products returned without prior authorization will be returned to the buyer. the buyer will pay all charges incurred in returni ng the product to the factory. vicor will pay all reshipment charges if the product was defective within the terms of this warrant y. information published by vicor has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. vicor reserves the right to make changes to any products without further notice to improve reliability, function, or design. vicor does not assume any liability arising out of the application or use of any product or circuit; neither does it convey any license under its patent rights nor the rights of othe rs. vicor general policy does not recommend the use of its components in life support applications wherein a failure or malfunction may directly threaten life or injury. per vicor terms and conditions of sale, the user of vicor components in life support appl i- cations assumes all risks of such use and indemnifies vicor against all damages.
|
